Uncategorized

three Effortless Do it yourself FLOATING Photo FRAMES AND HOW TO Lower PLEXIGLASS

By December 7, 2023

This submit about&nbsphow to make three Simple Do it yourself Floating Photograph Frames And How to Slash Plexiglass&nbspis sponsored by The Property Depot as aspect of the #THDProSpective Software. It also incorporates affiliate links. See&nbsppolicies.

Quick Do it yourself image frames are really a single of my most asked for tutorials and oddly enough, until finally now, I didn&rsquot have quite a few to share!

.

I essentially constructed my father a&nbspmassive Do it yourself tailor made photo frame as a Christmas gift a couple years in the past and shared the tutorial for it here.&nbspBut it used dowels, and a router, and it may possibly have been a small far more included than most folks are on the lookout for.

So, in this write-up, I&rsquom heading to show you how I created 3 diverse style Tremendous Easy Do-it-yourself floating photo frames with just two standard tools. I&rsquoll also show you how easy it is to cut plexiglass for them, far too!

.

So if you&rsquore ready to get building, enable&rsquos go! I&rsquove acquired the movie tutorial here and the move by phase under:

Applications AND Elements:

  • Miter saw&nbsp(or any wooden slicing saw is wonderful&ndashdoesn&rsquot have to be a MITER observed)
  • Nail Gun&nbsp(optional, just tends to make points more quickly)
  • Wooden Glue
  • &frac34&Prime sq. dowels
  • one&times2 boards
  • &frac14&Key x one ⅛&Key lattice trim
  • Thin Plexiglass Sheets
  • Ryobi Just one+ HP Slice Off Device&nbsp(utilized to slice plexiglass)
  • Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in place of clamps to hold parts while wood glue dries)
  • Turn buttons

A Take note About FLOATING Photograph Frames:

I&rsquom sharing how to make three unique model FLOATING image frames in this tutorial, but the to start with phase to building any of them is reducing the plexiglass to the measurement you want.

.

If you don&rsquot want to use plexiglass for your frames, you can skip this stage. But considering the fact that the graphics/photos I framed are &ldquofloating&rdquo within the body, they&rsquore basically sandwiched amongst two pieces of plexiglass. So plexiglass/acrylic is needed to be ready to &ldquofloat&rdquo your image.

.

To make factors easy to modify out in these frames, I also applied these convert buttons&mdashor I contact them twisty tabs&ndashon the back again to hold the plexiglass in place.&nbsp&nbsp

HOW TO Cut PLEXIGLASS

Typically, I have my neighborhood glass shop reduce my glass and plexiglass pieces for my tasks.&nbsp But since these plexiglass pieces will be smaller and numerous custom dimensions, it would be a great deal more cost-effective, more rapidly and a lot easier to just cut them myself.

.

I applied some&nbsp(about) ⅛&rdquo acrylic sheets from Property Depot.&nbsp They come in numerous sizes, all the way up to a 4&times8 sheet.&nbsp I just grabbed some 11x14s.

I designed some straightforward graphics on my laptop (PicMonkey&nbspand&nbspCanva&nbspare terrific for this!) and also employed a patch that I received a couple of yrs back at a conference for these frames.&nbsp i thought about this can use a image, a poster, cloth, regardless of what you want to body for this.

.

I laid them out on my sheet how I preferred the spacing, then marked wherever I needed to cut&ndashno measurements below&hellipjust eyeballing how I assumed the spacing around the impression appeared fantastic.

Now, I&rsquove utilized the inexpensive very little hand knife they declare will slash plexiglass in advance of and it was a terrible knowledge with quite inadequate outcomes.&nbsp I&rsquove also applied a jig observed to slice plexiglass and it melts, gets caught, then chips or cracks the sheet.

.

So THIS time, I tried&nbspthis new Ryobi One+ HP Compact Reduce Off Instrument&nbspwith a plastic reducing blade and was comprehensively amazed with how rapid and clear the cuts ended up.

When I very first noticed this software, I found it type of unusual searching.&nbsp But immediately after I used it, I comprehended the thought.&nbsp

.

It&rsquos fundamentally a hybrid involving a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety degrees.&nbsp

.

It&rsquos compact and light-weight and it&rsquos obtained a forward and reverse swap to transform the blade both of those directions.&nbsp It&rsquos also obtained a variable velocity cause&mdashwhich is fantastic for chopping plastic to help reduce melting.&nbsp

It will come with a plastic and drywall blade, a metal minimize off wheel, and a diamond blade for slicing tile and cement board.&nbsp You can discover much more about&nbspthe new Ryboi 1+ HP minimize off resource at the connection in this article if you&rsquore fascinated.

.

For chopping straight traces on the plexiglass, I just lined up a straight edge (scrap piece of wood), clamped and ran the metal blade guard from it to make the minimize.&nbsp You can skip the straight edge and freehand these cuts, also if you have a steady hand. (I don&rsquot haha!)

I did locate it slice most effective in this situation with the swap in reverse. It appeared to not melt that way.

.

I slash two parts identical in sizing for just about every product I was framing. Then, I was completely ready to start off generating the genuine floating photo frames.

Easy Diy FLOATING Image Body Type one

Type 1 is my private preferred, so I&rsquoll start off with it 😊

This certain floating photo body style and design needs&nbsp&frac34&Primary sq. dowels&nbspand&nbsp1&times2 board.&nbspIt is essentially just a 1&times2 wrapped all-around a sq. dowel body.

.

I made use of &frac34&rdquo square dowels for this and established up my miter saw to minimize 45 levels.&nbsp Now, you don&rsquot have to miter these.&nbsp You can leave it on ninety and make butt joints.&nbsp You also don&rsquot need to have a MITER noticed for this.&nbsp Any saw that you can cut quite straight with will do the job high-quality.

.

I mainly trimmed 4 parts of square dowel so that when healthy jointly, they&rsquod be just scarcely (like ⅛&Prime) even larger than the plexiglass piece I was placing in it.

I utilized wood glue to the corners and nailed them with each other with brad nails.&nbsp If you are affected person, and don&rsquot have a nail gun, simply glue and clamp right up until dry.

.

Immediately after the glue had dried, I slash to in good shape one&times2 pieces with 45 degree mitered corners close to this body.&nbsp Once again, butt joints are fine right here if you want to skip the mitered corners.

.

I glued and nailed these 1x2s around the edges leaving about &frac14&rdquo sticking out the back side of the plexiglass, so that when I put in the two ⅛&Key plexiglass pieces, it&rsquoll be flush across the again facet of the body.

Then, I screwed these twisty tabs into the back sides of the frame to hold the plexiglass in area.&nbsp I&rsquoll go back again and clear the sawdust off the plexiglass later, but for now, I established this off to the side to make the following frame.

Simple Do-it-yourself FLOATING Photograph FRAMES Design two

Fashion two is a tiny easier and is designed of&nbsp1x2s&nbspand&nbsp&frac14&rdquo thick by 1 ⅛&Key broad lattice trim.

I commenced by slicing down the lattice pieces so it would make a body that the plexiglass would match Within.&nbsp Again, just like right before, the mitered corners are optional.

The moment I had this lattice frame minimize, I measured its all round dimension and slice 1&times2 parts to make a body whose in general dimension matched that of the lattice body. See under one&times2 body laying on top of lattice body&ndashthey&rsquore the exact same dimensions.

I glued and nailed the one&times2 body alongside one another and clamped till dry. All over again, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps 🙂

.

Then, I flipped it upside down and glued the lattice body onto the back again.&nbsp I made use of a hefty item to hold it in location until eventually it was dry, then, I screwed twisty tabs on the back again to hold the plexiglass in position.&nbsp

Because the lattice is &frac14&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass parts are positioned inside, every thing should sit flush throughout the back just like the past body.

Once more, I&rsquoll go again and clean up the sawdust off afterwards, but for now, I moved on to the last style frame.

Simple Do it yourself FLOATING Picture Body Design three

Style 3 is the identical thought as type one, but as an alternative of working with 1x2s, I made use of&nbsp&frac14&Prime x 1 ⅛&Prime lattice trim&nbspto hold the frame a little thinner and additional minimalist seeking.

So, I slash&nbsp&frac34&rdquo sq. dowels&nbspto make a body the exact same dimensions or marginally more substantial than the plexiglass I was framing and glued and nailed it jointly.

Then, I cut lattice trim to wrap all around that frame.&nbsp

I glued the lattice trim on so that there was about &frac14&rdquo sticking off the again facet of the sq. dowel body so that when the two parts of ⅛&rdquo plexiglass are set up, it&rsquoll all be flush throughout the again.

.

I didn&rsquot have any brad nails shorter adequate to nail this body on, so I simply glued and clamped right up until it was dry.

If you don&rsquot have clamps, you can use painters tape to variety of wrap around the pieces to hold right up until the glue dries OR merely use some super glue or CA glue to aid keep items in put until finally the real wood glue is cured.

.

Then, just like the last two frames, I installed twisty tabs to maintain the plexiglass in location.

FLOATING Picture Body HANGING Selections

The ultimate move is thoroughly clean up and hanging.&nbsp I used some glass cleaner to thoroughly clean up all the noticed dust, then utilized a piece of double sided tape on the again plexiglass piece to make certain the shots continue to be in place, then put the frames back again with each other.

.

To hold, you can use your&nbspstandard sawtooth hangers&nbspfor this.

Or basically put it on a shelf.

.

OR, use a drill to drill holes into the corners to run some&nbspparacord&nbspand dangle it on a piece of wood dowel you screwed into the wall.

As you can see, generating picture frames doesn&rsquot have to be intricate.&nbsp This is a wonderful newbie job you can deal with with minimal resources and get as imaginative as you want.&nbsp

.

I really hung these graphics up in my desk area to assist retain me inspired whilst functioning alone from household proper now. So, now that my desk room is entire, I guess I must likely get back to operate 😊

I hope you&rsquove enjoyed this minimal task.&nbsp There are plenty additional coming your way, so be certain to subscribe to my e-newsletter below so you don&rsquot overlook out on what&rsquos coming future!

.

And don&rsquot fail to remember to pin this for afterwards!

Until finally subsequent time, pleased creating 😊

&nbsp

mm

Mofe Awala-Ale

Mofe is a writer and self-taught baker with a growing interest in beauty and health. When she is not working, she enjoys trying new beauty hacks and health trends.